Çözüldü P5QL Pro Mavi Ekran hatası

Bu konu çözüldü olarak işaretlenmiştir. Çözülmediğini düşünüyorsanız konuyu rapor edebilirsiniz.
U

uccergel

Hectopat
Katılım
30 Haziran 2012
Mesajlar
3
Oyun oynarken, bazen bilgisayar açılırken mavi ekran hatası alıyorum.

  • İşlemcim: Q8300 Quad Core 2.53 GHz 4Mb Cache 1333 FSB 45 NM
  • Anakartım: P5QL PRO INTEL P43/ICH10 DDR2 1066 MHz 1333 FSB
  • RAM :OCZ 2 Gb (2*1) KIT 1066 MHz FATALLITY DDR2 PC 8500
  • Ekran Kartı: HD 3850 512Mb GDDR3 256 Bit


Uzun zamandır çözmeye çalışıyorum ama çözemedim bir türlü. Yardımcı olursanız sevinirim.
 
Son düzenleyen: Moderatör:
Çözüm
Recep Baltaş
Dosyaları inceliyorum. Bu arada mavi ekran geldiğinde sistemin yeniden başlamaması için bu ayarı yapmanız gerek:

Mavi Ekran Hatalarında Sistem Yeniden Başlatmayı Devre Dışı Bırakma

Aldığın mavi ekran hatalarının her biri diğerinden farklı. Yani belirli bir sürücü ya da programdan kaynaklanmıyor hata. RAM'in bozuk olma ihtimali çok yüksek. Memtest86+ ile bir test et bakalım.

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: fltmgr.sys


BAD_POOL_HEADER


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x00000019 (0x00000003, 0x82b4ace0, 0x82b4aad8, 0x82b4aad8)


*** fltmgr.sys - Address 0x88972c77 base at 0x8896d000 DateStamp 0x4a5bbf11

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


PAGE_FAULT_IN_NONPAGED_AREA


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x00000050 (0xf98b61cc, 0x00000000, 0x82c7942b, 0x00000002)


*** ntkrnlpa.exe - Address 0x82ada8e3 base at 0x82a55000 DateStamp 0x4a5bc007

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


KERNEL_MODE_EXCEPTION_NOT_HANDLED


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x1000008e (0xc000001d, 0x82c174bf, 0x98b21460, 0x00000000)


*** ntkrnlpa.exe - Address 0x82c174bf base at 0x82a16000 DateStamp 0x4a5bc007

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: rdyboost.sys


DRIVER_IRQL_NOT_LESS_OR_EQUAL


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x000000d1 (0x01535242, 0x00000002, 0x00000001, 0x8afd83df)


*** rdyboost.sys - Address 0x8afd83df base at 0x8afce000 DateStamp 0x4a5bc19a

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


MEMORY_MANAGEMENT


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x0000001a (0x00041287, 0x00009c4c, 0x00000000, 0x00000000)


*** ntkrnlpa.exe - Address 0x82ac28e3 base at 0x82a3d000 DateStamp 0x4a5bc007


Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: mfeavfk.sys


KERNEL_MODE_EXCEPTION_NOT_HANDLED


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x1000008e (0xc0000005, 0x6811a3f6, 0x96b0766c, 0x00000000)


*** mfeavfk.sys - Address 0x93507ed7 base at 0x934f1000 DateStamp 0x4bba607a

Kod: 
A problem has been detected and Windows has been shut down to prevent damageto your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


KERNEL_MODE_EXCEPTION_NOT_HANDLED


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x1000008e (0xc0000005, 0x82b3d7ff, 0x826a0fec, 0x00000000)


*** ntkrnlpa.exe - Address 0x82b3d7ff base at 0x82a1d000 DateStamp 0x4a5bc007


Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


PAGE_FAULT_IN_NONPAGED_AREA


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x00000050 (0x807fbdc0, 0x00000000, 0x8ceee566, 0x00000000)


*** ntkrnlpa.exe - Address 0x82abe8e3 base at 0x82a39000 DateStamp 0x4a5bc007

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: atikmdag.sys


DRIVER_IRQL_NOT_LESS_OR_EQUAL


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x000000d1 (0x4c7b01d5, 0x0000000a, 0x00000000, 0x8e46e3bf)


*** atikmdag.sys - Address 0x8e46e3bf base at 0x8e218000 DateStamp 0x4bbbe1f7


Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: Ntfs.sys


NTFS_FILE_SYSTEM


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x00000024 (0x001904fb, 0x9c0ffa18, 0x9c0ff5f0, 0x88ef9c43)


*** Ntfs.sys - Address 0x88ef9c43 base at 0x88e60000 DateStamp 0x4a5bbf45
Tarihe göre sırala Puana göre sırala
Öncelikle mavi ekran ne sıklıkla geliyor? Eğer çok sık geliyorsa ve her defasında farklı bir kod çıkarıyorsa karşınıza, bunun nedeni genelde arızalı bellek modülleridir.

İlk olarak C:\Windows\minidump klasöründe ne var ne yok RAR'layıp MediaFire'a yükleyerek bizimle paylaşın. Bunlar, bilgisayarınız mavi ekran verdiğinde sistemin, hatanın olası kaynağını not düştüğü dosyaları içermekte. Bu dosyaları analiz edip sorunun kaynağına ineceğiz.

Belleklerinizi de test etmenizde fayda var. Bunun için şu konudaki aracı kullanabilirsiniz:

Memtest86+ USB'den Çalışan RAM Bellek Test Programı
 
Artı 0 Eksi
Dosyaları inceliyorum. Bu arada mavi ekran geldiğinde sistemin yeniden başlamaması için bu ayarı yapmanız gerek:

Mavi Ekran Hatalarında Sistem Yeniden Başlatmayı Devre Dışı Bırakma

Aldığın mavi ekran hatalarının her biri diğerinden farklı. Yani belirli bir sürücü ya da programdan kaynaklanmıyor hata. RAM'in bozuk olma ihtimali çok yüksek. Memtest86+ ile bir test et bakalım.

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: fltmgr.sys


BAD_POOL_HEADER


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x00000019 (0x00000003, 0x82b4ace0, 0x82b4aad8, 0x82b4aad8)


*** fltmgr.sys - Address 0x88972c77 base at 0x8896d000 DateStamp 0x4a5bbf11

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


PAGE_FAULT_IN_NONPAGED_AREA


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x00000050 (0xf98b61cc, 0x00000000, 0x82c7942b, 0x00000002)


*** ntkrnlpa.exe - Address 0x82ada8e3 base at 0x82a55000 DateStamp 0x4a5bc007

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


KERNEL_MODE_EXCEPTION_NOT_HANDLED


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x1000008e (0xc000001d, 0x82c174bf, 0x98b21460, 0x00000000)


*** ntkrnlpa.exe - Address 0x82c174bf base at 0x82a16000 DateStamp 0x4a5bc007

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: rdyboost.sys


DRIVER_IRQL_NOT_LESS_OR_EQUAL


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x000000d1 (0x01535242, 0x00000002, 0x00000001, 0x8afd83df)


*** rdyboost.sys - Address 0x8afd83df base at 0x8afce000 DateStamp 0x4a5bc19a

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


MEMORY_MANAGEMENT


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x0000001a (0x00041287, 0x00009c4c, 0x00000000, 0x00000000)


*** ntkrnlpa.exe - Address 0x82ac28e3 base at 0x82a3d000 DateStamp 0x4a5bc007


Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: mfeavfk.sys


KERNEL_MODE_EXCEPTION_NOT_HANDLED


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x1000008e (0xc0000005, 0x6811a3f6, 0x96b0766c, 0x00000000)


*** mfeavfk.sys - Address 0x93507ed7 base at 0x934f1000 DateStamp 0x4bba607a

Kod: 
A problem has been detected and Windows has been shut down to prevent damageto your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


KERNEL_MODE_EXCEPTION_NOT_HANDLED


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x1000008e (0xc0000005, 0x82b3d7ff, 0x826a0fec, 0x00000000)


*** ntkrnlpa.exe - Address 0x82b3d7ff base at 0x82a1d000 DateStamp 0x4a5bc007


Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: ntkrnlpa.exe


PAGE_FAULT_IN_NONPAGED_AREA


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x00000050 (0x807fbdc0, 0x00000000, 0x8ceee566, 0x00000000)


*** ntkrnlpa.exe - Address 0x82abe8e3 base at 0x82a39000 DateStamp 0x4a5bc007

Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: atikmdag.sys


DRIVER_IRQL_NOT_LESS_OR_EQUAL


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x000000d1 (0x4c7b01d5, 0x0000000a, 0x00000000, 0x8e46e3bf)


*** atikmdag.sys - Address 0x8e46e3bf base at 0x8e218000 DateStamp 0x4bbbe1f7


Kod: 
A problem has been detected and Windows has been shut down to prevent damage
to your computer.


The problem seems to be caused by the following file: Ntfs.sys


NTFS_FILE_SYSTEM


If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:


Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.


If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.


Technical Information:


*** STOP: 0x00000024 (0x001904fb, 0x9c0ffa18, 0x9c0ff5f0, 0x88ef9c43)


*** Ntfs.sys - Address 0x88ef9c43 base at 0x88e60000 DateStamp 0x4a5bbf45
 
Artı 0 Eksi
Çözüm
Uyarı! Bu konu 12 yıl önce açıldı.
Muhtemelen daha fazla tartışma gerekli değildir ki bu durumda yeni bir konu başlatmayı öneririz. Eğer yine de cevabınızın gerekli olduğunu düşünüyorsanız buna rağmen cevap verebilirsiniz.

Benzer konular

wishbone
  • Çözüldü
Çözüldü  Premiere Pro Mavi ekran Hatası
Mesaj
2
Görüntüleme
4B
wishbone
wishbone
MxKrav
  • Soru
Premiere Pro mavi ekran hatası
Mesaj
1
Görüntüleme
377
EgeN7
EgeN7
G
  • Çözüldü
Çözüldü  Premiere Pro Mavi Ekran Hatası
Mesaj
5
Görüntüleme
875
yika38
Y
T
  • Soru
H110M PRO-D sistemde mavi ekran hatası
Mesaj
0
Görüntüleme
169
Talha Günbaş
T
yusuffffff
  • Soru
Mavi ekran hatası Windows 10 Pro 20H2
Mesaj
3
Görüntüleme
758
yusuffffff
yusuffffff

Yeni konular

Yeni mesajlar

Geri
Yukarı