Arayüze koydukları kısıtlamaları gördükten sonra merak sardım bu modeme. Araştırma yaptığımda özel üretim olduğunu öğrendim. Haliyle TP-Link'in bu ürün için sayfası yok, normalde satılan ürün şu.
Elimdeki cihazın yazılım sürümü yanlış hatırlamıyorsam 17.12.27.01005 idi, küçük bir talihsizlik sonucu çalışmaz hale geldi. Aynısından tekrar aldığımda elime 20.05.16.01006 sürümlü model geçti. Arayüzden ibaret değilmiş yaptıkları değişiklikler, eskisinde boot sürecine müdahale edilemiyorken bu sürümde edilebiliyor. Hatta bir de root shell imkânı sunuyor.
Kullanıcı adı "root", şifre ise "8lK!5ikI60B@".
Elimde CP2102 olduğu için onu kullandım. 115200 baud rate kullanmanız gerekiyor, pinout şu şekilde:
Bir de 7 saat süren bir dump denemesi yaptık. İlgilenen arkadaşlar için link şu. Jefferson aracı ile açabilirsiniz.
Elimdeki cihazın yazılım sürümü yanlış hatırlamıyorsam 17.12.27.01005 idi, küçük bir talihsizlik sonucu çalışmaz hale geldi. Aynısından tekrar aldığımda elime 20.05.16.01006 sürümlü model geçti. Arayüzden ibaret değilmiş yaptıkları değişiklikler, eskisinde boot sürecine müdahale edilemiyorken bu sürümde edilebiliyor. Hatta bir de root shell imkânı sunuyor.
Kullanıcı adı "root", şifre ise "8lK!5ikI60B@".
Elimde CP2102 olduğu için onu kullandım. 115200 baud rate kullanmanız gerekiyor, pinout şu şekilde:
Bir de 7 saat süren bir dump denemesi yaptık. İlgilenen arkadaşlar için link şu. Jefferson aracı ile açabilirsiniz.
Kod:
HELO
CPUI
L1CI
HELO
CPUI
L1CI
4.1601-1.0.38-116.15
DRAM
----
PHYS
STRF
400H
PHYE
DDR2
SIZ4
SIZ3
SIZ2
SIZ1
DINT
USYN
LSYN
MFAS
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
FPS0
B002
0001
B003
0236
NAN3
RFS2
NAN5
Base: 4.16_01
CFE version 1.0.38-116.15 for BCM963268 (32bit,SP,BE)
Build Date: 2020年 05月 16日 星期六 17:15:05 CST (root@tplink)
Copyright (C) 2000-2013 Broadcom Corporation.
Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
NAND ECC Hamming, page size 0x800 bytes, spare size used 64 bytes
NAND flash device: ESMT, id 0xc8d1 block 128KB size 131072KB
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Boot image (0=latest, 1=previous) : 0
Default host ramdisk file name :
Default ramdisk store address :
Board Id (0-29) : 963168XF
Number of MAC Addresses (1-32) : 11
Base MAC Address : c5:05:c0:99:70:01
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
*** Press 't' to stop auto run (0.3 seconds) ***
CFE>
web info: Waiting for connection on socket 0.[J
CFE> help
Available commands:
dn Dump NAND contents along with spare area
phy Set memory or registers.
sm Set memory or registers.
dm Dump memory or registers.
db Dump bytes.
dh Dump half-words.
dw Dump words.
e Erase NAND flash
r Run program from flash image or from host depend on [f/h] flag
p Print boot line and board parameter info
c Change booline parameters
f Write image to the flash
i Erase persistent storage data
a Change board AFE ID
b Change board parameters
reset Reset the board
pmdio Pseudo MDIO access for external switches.
spi Legacy SPI access of external switch.
force override chipid check for images.
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0
CFE> p
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Boot image (0=latest, 1=previous) : 0
Default host ramdisk file name :
Default ramdisk store address :
Board Id (0-29) : 963168XF
Number of MAC Addresses (1-32) : 11
Base MAC Address : c5:05:c0:99:70:01
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
*** command status = 0
CFE> reset
Resetting board in 0 seconds...
HELO
CPUI
L1CI
HELO
CPUI
L1CI
4.1601-1.0.38-116.15
DRAM
----
PHYS
STRF
400H
PHYE
DDR2
SIZ4
SIZ3
SIZ2
SIZ1
DINT
USYN
LSYN
MFAS
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
FPS0
B002
0001
B003
0236
NAN3
RFS2
NAN5
Base: 4.16_01
CFE version 1.0.38-116.15 for BCM963268 (32bit,SP,BE)
Build Date: 2020年 05月 16日 星期六 17:15:05 CST (root@tplink)
Copyright (C) 2000-2013 Broadcom Corporation.
Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
NAND ECC Hamming, page size 0x800 bytes, spare size used 64 bytes
NAND flash device: ESMT, id 0xc8d1 block 128KB size 131072KB
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Boot image (0=latest, 1=previous) : 0
Default host ramdisk file name :
Default ramdisk store address :
Board Id (0-29) : 963168XF
Number of MAC Addresses (1-32) : 11
Base MAC Address : c5:05:c0:99:70:01
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
*** Press 't' to stop auto run (0.3 seconds) ***
Booting from latest image (address 0xb9d80000, flash offset 0x01d80000) ...
Decompression OK!
Entry at 0x80402740
Starting program at 0x80402740
Linux version 3.4.11-rt19 (root@tplink) (gcc version 4.6.2 (Buildroot 2011.11) ) #18 SMP PREEMPT Sat May 16 17:21:01 CST 2020
963168XF prom init
CPU revision is: 0002a080 (Broadcom BMIPS4350)
DSL SDRAM reserved: 0x132000
Determined physical RAM map:
memory: 03ece000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003ece
Movable zone start PFN for each node
Early memory PFN ranges
0: 0x00000000 -> 0x00003ece
On node 0 totalpages: 16078
free_area_init_node: node 0, pgdat 80515e40, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11888 pages, LIFO batch:1
PERCPU: Embedded 7 pages/cpu @81083000 s5488 r8192 d14992 u32768
pcpu-alloc: s5488 r8192 d14992 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15952
Kernel command line: ro noinitrd irqaffinity=0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 57996k/64312k available (4096k kernel code, 6316k reserved, 1049k data, 216k init, 0k highmem)
Preemptible hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 397.31 BogoMIPS (lpj=198656)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Broadcom Logger v0.1 May 16 2020 17:15:59
CPU revision is: 0002a080 (Broadcom BMIPS4350)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Brought up 2 CPUs
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0xa0f00000-0xa0ffffff]
pci_bus 0000:00: root bus resource [io 0xa2000000-0xa200ffff]
pci 0000:00:00.0: [14e4:435f] type 00 class 0x028000
pci 0000:00:00.0: reg 10: [mem 0x10004000-0x10005fff]
pci 0000:00:09.0: [14e4:6300] type 00 class 0x0c0310
pci 0000:00:09.0: reg 10: [mem 0x10002600-0x100026ff]
pci 0000:00:0a.0: [14e4:6300] type 00 class 0x0c0320
pci 0000:00:0a.0: reg 10: [mem 0x10002500-0x100025ff]
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0x11000000-0x11efffff]
pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
pci 0000:01:00.0: [14e4:6326] type 01 class 0x060400
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PCI bridge to [bus 02-02]
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
bcmleg_spi bcmleg_spi.0: master is unqueued, this is deprecated
skbFreeTask created successfully
[0;34mBLOG v3.0 Initialized[0m
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 May 16 2020 17:19:17 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS mismatch (64 != 16), using 16 bytes
bcm_tstamp initialized, (hpt_freq=200000000 2us_div=200 2ns_mult=5 2ns_shift=0)
exFAT: Version 1.2.9
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
msgmni has been set to 113
io scheduler noop registered (default)
Broadcom NAND controller (BrcmNand Controller)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0
brcmnand_read_id: CS0: dev_id=c8d18095
After: NandSelect=40000001, nandConfig=15142200
DevId c8d18095 may not be supported. Will use config info
Spare Area Size = 16B/512B
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 6574845b
timing2 not adjusted: 00001e96
ECC level changed to 15
OOB size changed to 16
BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0
Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=c8d18095, tim1=6574845b, tim2=00001e96
BrcmNAND version = 0x0400 128MB @00000000
brcmnand_scan: B4 nand_select = 40000001
brcmnand_scan: After nand_select = 40000001
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_64
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0
brcmnandCET: Status -> Loaded
Creating 6 MTD partitions on "brcmnand.0":
0x000001d80000-0x000003ae0000 : "rootfs"
0x000000020000-0x000001d80000 : "rootfs_update"
0x000003b00000-0x000003f00000 : "data"
0x000000000000-0x000000020000 : "nvram"
0x000001d80000-0x000003ae0000 : "image"
0x000000020000-0x000001d80000 : "image_update"
PPP generic driver version 2.4.2
NET: Registered protocol family 24
usbcore: registered new interface driver usblp
brcmboard: brcm_board_init entry
WIFI: Button Interrupt 0x3 is enabled
RESET: Button Interrupt 0x0 is enabled
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8016 is enabled
DYING GASP IRQ initialized
Register flash device: flash0
Serial: BCM63XX driver $Revision: 3.00 $
[0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)[0m
ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX
ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
GACT probability NOT on
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (906 buckets, 5120 max)
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
ebt_ftos registered
ebt_wmm_mark registered
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (jffs2 filesystem) readonly on device 31:0.
Freeing unused kernel memory: 216k freed
starting pid 244, tty '': '/etc/init.d/rcS'
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
chipinfo: module license 'proprietary' taints kernel.
Disabling lock debugging due to kernel taint
brcmchipinfo: brcm_chipinfo_init entry
bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.6 May 16 2020 17:23:40
Broadcom Ingress QoS Module Char Driver v0.1 May 16 2020 17:21:50 Registered<243>[0m
Broadcom Ingress QoS ver 0.1 initialized
NBUFF v1.0 Initialized
[0;36;44mInitialized fcache state[0m
[0;36;44mBroadcom Packet Flow Cache Char Driver v2.2 May 16 2020 17:21:51 Registered<242>[0m
Created Proc FS /procfs/fcache
[0;36;44mBroadcom Packet Flow Cache registered with netdev chain[0m
[0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.[0m
[0;35m[FHW] pktDbgLvl[0xc00d75e0]=0[0m
[0;34m[FHW] fhw_construct: [0m
[0;36;44mInitialized Fcache HW accelerator layer state[0m
flwStatsThread created
[0;36;44mConstructed Broadcom Packet Flow Cache v2.2 May 16 2020 17:21:51[0m
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM63168D0 Ethernet Network Device v0.1 May 16 2020 17:23:34
ETH Init: Ch:0 - 200 tx BDs at 0xa30fb000
ETH Init: Ch:1 - 200 tx BDs at 0xa30fa000
ETH Init: Ch:0 - 600 rx BDs at 0xa30e2000
ETH Init: Ch:1 - 100 rx BDs at 0xa3025800
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0.2: <Int sw port: 0> <Logical : 00> PHY_ID <0x00000001 : 0x01> MAC : 98:DE:D0:7C:D3:10
eth0.3: <Int sw port: 1> <Logical : 01> PHY_ID <0x00000002 : 0x02> MAC : 98:DE:D0:7C:D3:10
eth0.4: <Int sw port: 2> <Logical : 02> PHY_ID <0x00000003 : 0x03> MAC : 98:DE:D0:7C:D3:10
eth1: <Int sw port: 3> <Logical : 03> PHY_ID <0x00000044 : 0x04> MAC : 98:DE:D0:7C:D3:10
eth0.5: <Int sw port: 4> <Logical : 04> PHY_ID <0x00800010 : 0x10> MAC : 98:DE:D0:7C:D3:10
Energy Efficient Ethernet: Disabled
[0;36;44mBroadcom Packet Flow Cache HW acceleration enabled.[0m
[0;34m[NTC arl] arlEnable : Enabled ARL binding to Flow Cache[0m
Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 May 16 2020 17:21:50 Registered <245>
Broadcom 802.1Q VLAN Interface, v0.1
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: setting latency timer to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: setting latency timer to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
hub 1-0:1.0: over-current condition on port 2
dns_init
PPP MPPE Compression module registered
PPTP driver version 0.8.5
Please press Enter to activate this console. [ dm_readFile ] 2061: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
[ initKernelMonitorFd ] 525: kernelMonitormonitor task is initialized pid= 468
Fd=6
[ initKernelMonitorFd ] 543: registered fd 6 with kernel monitor
send 2001 error No such file or directory ,pid 353
Success
ioctl: No such device
Generating 2048 bit rsa key, this may take a while...
Generating 1024 bit dss key, this may take a while...
ADDRCONF(NETDEV_UP): eth0.4: link is not ready
device eth0.4 entered promiscuous mode
Success
ADDRCONF(NETDEV_UP): eth0.3: link is not ready
device eth0.3 entered promiscuous mode
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
Success
ADDRCONF(NETDEV_UP): eth0.2: link is not ready
device eth0.2 entered promiscuous mode
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
Success
ADDRCONF(NETDEV_UP): eth0.5: link is not ready
device eth0.5 entered promiscuous mode
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
Success
[DBG:700] ADSL dr*** dslThread dslPid=555
BcmAdsl_Initialize=0xC016C050, g_pFnNotifyCallback=0xC01A5790
iver returns error
[ oal_dsl_isAtmConnection ] 3918: Failed to freshAdslMibInfo
[DBG:939] ADSL driver returns error
lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000
pSdramPHY=0xA3FFFFF8, 0x1B77B3 0xDEADBEEF
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
*** PhySdramSize got adjusted: 0xF7844 => 0x12BD20 ***
AdslCoreSharedMemInit: shareMemSize=25280(25280)
AdslCoreHwReset: pLocSbSta=83b98000 bkupThreshold=3072
AdslCoreHwReset: AdslOemDataAddr = 0xA3FB6278
***BcmDiagsMgrRegisterClient: 0 ***
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: Ch:0 - 600 rx BDs at 0xa3b96000
XTM Init: Ch:1 - 16 rx BDs at 0xa2c7ae80
bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
Public key portion is:
ssh-dss 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 admin@TD-W9970
Fingerprint: sha1!! 11:f7:02:a0:4a:b0:ea:05:6b:77:7c:1e:06:e6:93:ad:84:d9:8f:91
open DNS error: No such file or directory
[ oal_sys_getOldTZInfo ] 435: Open TZ file error!
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQDCud5uZOtwDpyu90LbZ/HkHSQSVYR0p8qqUZauw6GvVvOInb2V+bdH1+1IBPE2mUFFMkoomIitTD0knCKw/8pVCb9mALzh3M/j3s14upZ3KAGO1oxzVmeZIEEwAMAN8NJjjlYZJ0DGii+aPiEDV6r1Q85UIlQnKRHe5wAfA7rM/dmqFSVbvw+1EsJq7ylCQ7UIPri7sb/zDkpGS6DPG0NAs/o1RkwGVe6EXWFqzLrO07qMiHwZZwjviIFRUpF1drLUqGvOGPsdlF5Pjq6ZyL7BAfIER/M7uOhV9EFDkq/5iugceLGN5uxG25lBQ/qvSy+bqDiVuU8does9qETMEauL admin@TD-W9970
Fingerprint: sha1!! b3:f7:4e:d1:f1:5b:39:a2:ff:58:1e:c1:02:71:2e:9b:07:54:9c:57
--SMP support
wl: dsl_tx_pkt_flush_len=338
wl: norm_wmark_tot=400, pktc_wmark_tot=2048
wl 0000:00:00.0: setting latency timer to 64
wl: passivemode=1
wl0: creating kthread wl0-kthrd
wl: napimode=0
Neither SPROM nor OTP has valid image
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm6362_map.bin
wl: updating srom from flash...
wl: updating srom from flash...
srom rev:8
wl0: allocskbmode=1 currallocskbsz=256
wl0: Broadcom BCM435f 802.11 Wireless Controller 6.37.14.4803.cpe4.16L01.0-kdb
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Setting SSID: "TurkTelekom_TD310"
wlctl: Unsupported
wlctl: Not up
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x1004
device wl0 entered promiscuous mode
br0: port 5(wl0) entered forwarding state
br0: port 5(wl0) entered forwarding state
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 123; error = Address already in use
igmpd# Err: setsockopt - MCAST_JOIN_GROUP
igmpd# file: src/igmp_ifinfo.c;line: 90; error = Address already in use
igmpd# Err: setsockopt - MRT_ADD_VIF
brctl: iface wl0.2: No such device
ioctl - SIOCGIFINDEX: No such device
brctl: iface wl0.3: No such device
ioctl - SIOCGIFINDEX: No such device
brctl: iface wl0.4: No such device
ioctl - SIOCGIFINDEX: No such device
[ rsl_initLanWlanObj ] 9542: if name = wlan1
[ rsl_initLanWlanObj ] 9542: if name = wlan2
[ rsl_initLanWlanObj ] 9542: if name = wlan3
send 2030 error No such file or directory ,pid 353
send 2030 error No such file or directory ,pid 353
send 2030 error No such file or directory ,pid 353
send 2030 error No such file or directory ,pid 353
send 2030 error No such file or directory ,pid 353
send 2030 error No such file or directory ,pid 353
send 2030 error No such file or directory ,pid 353
send 2030 error No such file or directory ,pid 353
killall: dnsmasq: no process killed
[ rsl_getManagementServerObj ] 375: cannot set connectionRequestURL yet because no WAN intf is up
[ rsl_getManagementServerObj ] 375: cannot set connectionRequestURL yet because no WAN intf is up
[ rsl_getManagementServerObj ] 375: cannot set connectionRequestURL yet because no WAN intf is up
ip6tables: No chain/target/match by that name.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
radvd starting
[Jan 01 03:00:44] radvd: no linklocal address configured for br0
[Jan 01 03:00:44] radvd: error parsing or activating the config file: /var/tmp/dconf/radvd_br0.conf
sh: pwrctl: not found
ADDRCONF(NETDEV_UP): eth1: link is not ready
sh: pwrctl: not found
sh: pwrctl: not found
[ rsl_wan_calWanReservedMacFromLanMac ] 1207: flashmac=98:DE:D0:7C:D3:10
[ rsl_wan_calWanReservedMacFromLanMac ] 1207: flashmac=98:DE:D0:7C:D3:10
[ rsl_wan_calWanReservedMacFromLanMac ] 1207: flashmac=98:DE:D0:7C:D3:10
sh: can't create /proc/sys/net/ipv6/conf/ptm0.55/disable_ipv6: nonexistent directory
ifconfig: ioctl 0x8913 failed: No such device
[ rsl_wan_calWanReservedMacFromLanMac ] 1207: flashmac=98:DE:D0:7C:D3:10
eth1.55 MAC address set to 98:DE:D0:7C:D3:10
netdev path : eth1.55 -> eth1
BCMVLAN : eth1 mode was set to RG
Created new Tag Rule: dev=eth1, dir=1, tags=0, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=0, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=1, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=2, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=1, id=1
Created new Tag Rule: dev=eth1, dir=0, tags=2, id=1
eth1.55 MAC address set to 98:DE:D0:7C:D3:11
device eth1 entered promiscuous mode
[ rsl_wan_calWanReservedMacFromLanMac ] 1207: flashmac=98:DE:D0:7C:D3:10
sh: can't create /proc/sys/net/ipv6/conf/ptm0.35/disable_ipv6: nonexistent directory
ifconfig: ioctl 0x8913 failed: No such device
[ wan_conn_pppoeConn ] 089: L2 interface not exist(up), don't start pppd!
[ rsl_wan_calWanReservedMacFromLanMac ] 1207: flashmac=98:DE:D0:7C:D3:10
eth1.35 MAC address set to 98:DE:D0:7C:D3:10
netdev path : eth1.35 -> eth1
BCMVLAN : eth1 mode was set to RG
Created new Tag Rule: dev=eth1, dir=1, tags=0, id=1
Created new Tag Rule: dev=eth1, dir=0, tags=0, id=1
Created new Tag Rule: dev=eth1, dir=0, tags=1, id=2
Created new Tag Rule: dev=eth1, dir=0, tags=2, id=2
Created new Tag Rule: dev=eth1, dir=0, tags=1, id=3
Created new Tag Rule: dev=eth1, dir=0, tags=2, id=3
eth1.35 MAC address set to 98:DE:D0:7C:D3:11
[ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid.
[ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid.
[ read_dhcpc_config ] 113: error, unable to open config file: /var/tmp/dconf/udhcpc.conf
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
Sorry, rule does not exist.
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
[ rsl_setStorageServiceObj ] 1256: mountFlag is 3,We start usb server
killall: ushare: no process killed
[ cwmp_parseAcsInfo ] 1235: No available connection for hostGetByName
uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server.
Benjamin Zores (C) 2005-2007, for GeeXboX Team.
See http://ushare.geexbox.org/ for updates.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
[ dm_getObjNode ] 762: Object(oid = 0)'s infomation is not exist.
[ dm_getObj ] 660: Get object information failed. object oid = 0
[ generalInitPageAttribute ] 2088: Get object for oid 0 error, ret = 9804
open DNS error: No such file or directory
[ cwmp_parseAcsInfo ] 1235: No available connection for hostGetByName
starting pid 354, tty '': '/sbin/getty -L ttyS0 115200 vt100'
TD-W9970 login: root
Password:
Jan 1 03:01:27 login[354]: root login on 'console'
~ #
Son düzenleyen: Moderatör: