Daha fazla
- Meslek
- Judge Dredd
StorCenter ix2-200 Cloud Edition Firmware Version 3.2.3.9273 - Release date 01/09/2012
New Version out: Firmware 3.2.6.21659
New features:
This update is not data destructive and will upgrade your current version, however, ALWAYS back up your data before performing any firmware update.
New features and changes
Iomega StorCenter version 3.2.3 contains the following new features:
allows you to back up and restore system configuration information. Backing up a
configuration saves various system properties, including users, groups, device
identification, and Share names and permissions.
schedule to turn your Iomega StorCenter on and off. Scheduled Power can be
one-time events, or recurring events. When you create a power schedule, you can
set the day and time to power down the device. You can also set power on times.
This is supported on px12-350r (ix12), px4-300r, px4-300d, and px6-300d only.
your Iomega StorCenter when a specific signal is sent over the network.
This is supported on px12-350r (ix12), px4-300r, px4-300d, and px6-300d only.
you to create an encrypted volume with an assigned password; thus securing the
data on the encrypted volume. Data on the encrypted volume is only accessible
when using the assigned password.
This is only available on PX devices and ix12.
Iomega StorCenter system.
third-party applications. These add-on applications extend the functionality and
flexibility of your StorCenter.
for Bosch camera support.
SFTP requires limited system resources, and is useful for secure transferring of
data between computers over a network. SFTP reads and writes files from/to a
remote server to an Iomega StorCenter device.
Installation Instructions:
[TBODY]
[/TBODY]
New Version out: Firmware 3.2.6.21659
New features:
- Configuration Capture and Restore — allows users to capture a configuration and re-create it on other StorCenter devices of the same hardware type.
Secure FTP (SFTP)
Video Surveillance enhancements
- XFS performance improvements
- SMART enhancements
- Minor bug fixes (see below for more details)
This update is not data destructive and will upgrade your current version, however, ALWAYS back up your data before performing any firmware update.
New features and changes
Iomega StorCenter version 3.2.3 contains the following new features:
- Configuration Backup and Restore
allows you to back up and restore system configuration information. Backing up a
configuration saves various system properties, including users, groups, device
identification, and Share names and permissions.
- Scheduled Power
schedule to turn your Iomega StorCenter on and off. Scheduled Power can be
one-time events, or recurring events. When you create a power schedule, you can
set the day and time to power down the device. You can also set power on times.
This is supported on px12-350r (ix12), px4-300r, px4-300d, and px6-300d only.
- Wake on LAN
your Iomega StorCenter when a specific signal is sent over the network.
This is supported on px12-350r (ix12), px4-300r, px4-300d, and px6-300d only.
- Encrypted File System
you to create an encrypted volume with an assigned password; thus securing the
data on the encrypted volume. Data on the encrypted volume is only accessible
when using the assigned password.
This is only available on PX devices and ix12.
- SMART Monitor
Iomega StorCenter system.
- Partner Application Download
third-party applications. These add-on applications extend the functionality and
flexibility of your StorCenter.
- Video Surveillance Enhancements - Bosch Camera & Resolution Settings
for Bosch camera support.
- SFTP (Secure File Transfer Protocol)
SFTP requires limited system resources, and is useful for secure transferring of
data between computers over a network. SFTP reads and writes files from/to a
remote server to an Iomega StorCenter device.
- Resolved issues
- The following issues have been resolved in version 3.2.3:
- 15538 Email distribution limitation.
- 1499 A maximum of 3,000 files can be displayed in the Iomega StorCenter Console Interface.
- 7152 QuikTransfers can be overwritten when changing removable media on the same drive.
- 7983 Multiple Copy Jobs running simultaneously can cause device to stop responding.
- 16729 404 error on Copy Jobs or QuikTransfers with USB stick device.
- 432 Pictures are not deleted from some cameras after transfer.
- 11332 Device does not scan media folders after adding media files.
- 18484 On px6, removing all drives via hot swap requires reboot.
- 11832 Iomega StorCenter can take a long time to load after main LED is solid blue.
- 16087 iSCSI page not reporting correct free space.
- 14160 Personal Cloud does not support double-byte characters.
- 13301 Personal Cloud copy status incorrectly reports slower speed than actual speed.
- 1627 Safari issue with reporting language region.
- 15662 Fedora versions 10 and 14 can not find device on the network.
- 15314 Secure copy to Rsync server results in incorrect email notification.
- 11956 Computers running 32-bit Linux 2.6.32 can have problems accessing an Iomega StorCenter.
- 17075 When an error occurs during the transfer of QT job, backup LED should flash in pattern.
- 15104 After disabling "Add shortcuts" on Linux, shortcuts are still created on desktop.
- 12818 MS initiator cannot find old iSCSI luns by iSNS server after upgrade.
- 17676 PersonalCloudModify API now supports exposing ports 80 and 443.
- 17875 Mozy Backup becomes disabled if ESC is pressed on confirmation pop up.
- 18379 iSCSI with modified access restrictions can still be found via iSNS server.
- 18505 No warning message when add/modify a VLAN tag to notify users.
- 18531 Wrong error appears during copy job when the FROM folder doesn't exist.
- 18532 Copy Jobs: Error log not created and “Failed to load resource error” appears in console when copy job failed.
- 18606 Iomega StorCenter device should not allow an upgrade with a different platform build.
- 18623 Sometimes device won't be restarted after changing device name in Active Directory mode.
- 18632 Using two of the same brand of USB drive may cause QT failure.
- 18701 iSCSI: Cannot connect iSCSI (found via iSNS) after recreating pool.
- 18703 Could not list all volumes when numbers of volumes exceeds 60.
- 18724 Copy Jobs: Files are copied to root fs when USB flash drive is source.
- 18746 In Internet Explorer 7, apply button cannot be activated by changing jumbo frame value of a vNIC.
- 19095 Cannot create a new pool after a total drive swap.
- 19096 Unit powers off when authorizing drive overwrite.
- 19347 Can't add new drives to a 2-drive RAID1 pool.
- 16470 IP address not refreshing after modification.
- 19456 Copy Job username should be re-entered after upgrade.
- 15526 Unable to view ico pictures in Internet Explorer 8.
- 18650 Deleting pool to which files are being copied can result in invalid error.
- 19085 Pools info on destination device may display incorrectly.
- 19472 Storage Pool behavior inconsistent after factory reset.
- 19492 Quota value for Administrator can not be properly set.
- 19493 After restarting device, redundant partitions appear.
- 18624 Share names longer than 12 characters may overlap in the System Status page.
- 19476 Secure Delete in Active Directory mode may require reset.
- 19399 Time Machine not functional in Mac Lion OS.
- 7726 iTunes version 8 for Windows not compatible with media server.
- 4202 Cannot view live video when accessing device remotely.
- 19706 May not be able to transfer files via TFTP after upgrade.
- 18301 When creating a Share, ‘working’ indicator does not disappear automatically.
- 19500 Files copied to the device using WebDAV may not be accessible to all users.
- 19829 King to Mirage upgrade on ix4-200d failed iSCSI in ESX.
- 19488 Cannot add new drive to ix12 after upgrading to Mirage.
- 18370 “View Live Camera” link in VS broken over Personal Cloud.
- 19733 Wrong source/destination path in Copy Jobs when pool name contains blank spaces when upgraded from PWIII to Mirage.
- 19766 Total drive size and capacity increases when opening or canceling the DM settings.
- 19763 CPU utilization is always 100%.
- 19427 New Volume created during share creation succeeds with invalid volume size.
- 19339 HDD not reused when non-catastrophic event happens.
- 19833 Size may display incorrectly in Change volume allocation paged new.
- 19742 Unable to reflect the volume “vol1” name in the Volume page.
- 19433 Deleting a pool during TimeMachine displays an incorrect error message.
- 19472 Storage Pool behavior inconsistent after factory reset.
- 18565 Refreshing the Drive Management page during creation of RAID pool may cause the device to become unresponsive.
- 16533 Hard drive does not spin down on Samba 3.5.6.
- 18680 Cannot import users and groups when devices join trusted domain.
- 19764 Modifying GID can result in deletion of users.
- 18478 Incoming one-way trust domain should not be listed.
- 19472 Storage Pool behavior inconsistent after factory reset.
- 19085 Pools info on destination device may display incorrectly.
- 20007 Copy Jobs not displaying correctly.
- 17328 File sizes larger than 1GB fails to upload to Amazon S3.
Installation Instructions:
- Download the ix2-200-3.2.3.9273.tgz file to your computer.
Internet Explorer Users: When the file is downloaded with Internet Explorer, the file which shows as a .TGZ file, maybe be downloaded as a .GZ file. This is a product of file MIME types built into Internet Explorer. This file is still recognized by the device as an update file.
Mac Users: Mac OS X will automatically try to decompress this file once it is downloaded. In most cases decompression will fail. This is normal. You will be using the compressed .tgz file for the installation. Do NOT try to decompress this file. - Log in to the StorCenter device and navigate to the management console.
- Click on the System icon in the left column, and click on Software Updates.
- In the Add Software popup box, click Browse... and select the ix2-200-3.2.3.9273.tgz file.
- Click on Upload and allow the file to upload to your device.
- When the update is uploaded to the Iomega NAS device, the Status column will say Ready to apply.
- Click Apply all pending updates to apply the update or updates. The software updates will be applied to your device. If you want to remove the update without applying changes, click the trash can icon the Action column.
CAUTION! Do not shut down or restart the device during the update process as this can damage the device. The software update will temporarily make the device inaccessible. The device will restart once the software is installed. If multiple updates are ready, all of them will be applied, requiring only one reboot. Be sure no critical files are being accessed.
| Download Now |
|
Son düzenleyen: Moderatör:
