Ardunio UNO ile ne yapılabilir?

blacknight7_ dedi:

#include <Mouse.h>
int horzPin = A1; // Analog output of horizontal joystick pin
int vertPin = A0; // Analog output of vertical joystick pin
int selPin = 8; // select button pin of joystick
int selPin1 = 9; //sağ
int selPin2 = 7; //orta

int vertZero, horzZero; // Stores the initial value of each axis, usually around 512
int vertValue, horzValue; // Stores current analog output of each axis
const int sensitivity = 100 ; // Higher sensitivity value = slower mouse, should be <= about 500
int mouseClickFlag = 0;
int mouseClickFlag1 = 0;
int mouseClickFlag2 = 0;

//int invertMouse = 1; //Invert joystick based on orientation
int invertMouse = -1; //Noninverted joystick based on orientation

void setup()
{
Serial.begin(9600);
pinMode(horzPin, INPUT); // Set both analog pins as inputs
pinMode(vertPin, INPUT);
pinMode(selPin, INPUT); // set button select pin as input
digitalWrite(selPin, HIGH); // Pull button select pin high
digitalWrite(selPin1, HIGH); // Pull button select pin high
digitalWrite(selPin2, HIGH); // Pull button select pin high
delay(500); // short delay to let outputs settle
vertZero = analogRead(vertPin); // get the initial values
horzZero = analogRead(horzPin); // Joystick should be in neutral position when reading these

Mouse.begin(); //Init mouse emulation
}

void loop()
{
vertValue = analogRead(vertPin) - vertZero; // read vertical offset
horzValue = analogRead(horzPin) - horzZero; // read horizontal offset


if (vertValue != 0)
Mouse.move(0, (invertMouse * (vertValue / sensitivity)) * -1, 0); // move mouse on y axis
if (horzValue != 0)
Mouse.move((invertMouse * (horzValue / sensitivity)) * 1, 0, 0); // move mouse on x axis

if ((digitalRead(selPin) == 0) && (!mouseClickFlag)) // if the joystick button is pressed
{
mouseClickFlag = 1;
Mouse.press(MOUSE_LEFT); // click the left button down
}
else if ((digitalRead(selPin)) && (mouseClickFlag)) // if the joystick button is not pressed
{
mouseClickFlag = 0;
Mouse.release(MOUSE_LEFT); // release the left button
}
if ((digitalRead(selPin1) == 0) && (!mouseClickFlag1)) // if the joystick button is pressed
{
mouseClickFlag1 = 1;
Mouse.press(MOUSE_RIGHT); // click the left button down
}
else if ((digitalRead(selPin1)) && (mouseClickFlag1)) // if the joystick button is not pressed
{
mouseClickFlag1 = 0;
Mouse.release(MOUSE_RIGHT); // release the left button
}
if ((digitalRead(selPin2) == 0) && (!mouseClickFlag2)) // if the joystick button is pressed
{
mouseClickFlag2 = 1;
Mouse.press(MOUSE_MIDDLE); // click the left button down
}
else if ((digitalRead(selPin2)) && (mouseClickFlag2)) // if the joystick button is not pressed
{
mouseClickFlag2 = 0;
Mouse.release(MOUSE_MIDDLE); // release the left button
}
}
kod bu benim kullandığım.
Arduino Pro Micro Klon
yeteri kadar jumper kablo

IC184 Plastik Renkli Mantar Tip Buton - Siyah Satın Al | Robotistan

IC184 Plastik Renkli Mantar Tip Buton - Siyah en uygun fiyatla Robotistan'da! Aynı gün kargo, kapıda ödeme ve taksit avantajlarıyla hemen sipariş verin!

www.robotistan.com

iki tane bundan

2 Eksenli Joystick Kartı Satın Al | Robotistan

2 Eksenli Joystick Kartı en uygun fiyatla Robotistan'da! Aynı gün kargo, kapıda ödeme ve taksit avantajlarıyla hemen sipariş verin!

www.robotistan.com

bi de bu.
tipi biraz çirkin ama yedek gibi bişey ihtiyaçtan yaptım zaten.

Genişletmek için tıkla...